ValueCut menu - 3.03A-03
| ValueCut User menu - 3.03GA | ||
| Misc menu | ||
| Auto Unrolled Media | Enabled | |
| Disabled | ||
| Vacuum | Enabled | |
| Disabled | ||
| First back to Origin | Enabled | |
| Disabled | ||
| AAS Offset | X: -0,700 | |
| Y: 0,150 | ||
| Paper Saving Mode | Length Expanded Mode | |
| Width Expanded Mode | ||
| Both Expanded Mode | ||
| Both Unexpanded Mode | ||
| Set Communication | 9600 | |
| n | ||
| 8 | ||
| 1 | ||
| p | ||
| Firmware | 3.03GA | Note: G in FMW file name > gear ratio |
| FPGA | 1.1 | |
| VC-1800 | ||
| Select Language | English | |
| Francais | ||
| Türkce | ||
| Polski | ||
| Ingles | ||
| Japanese | ||
| Deutsch | ||
| Italian | ||
| Espanol | ||
| Select Unit | Metric (cm/g) | |
| English (inch/g) | ||
| Image Scale Length | 500mm | |
| Image Scale Width | 500mm | |
| AAS Length Scale | 100% | |
| AAS Width Scale | 100% | |
| Cut Test | ||
| Square Cut | ||
| Redo Jobs in Memory | Recut # copies | |
| Blade Length Adjust | Set Length 0,000mm | Test Blade Holder |
| Ratio Setting | 100% | |
| Pattern Setting | Arrow | |
| Cross | ||
| Speed | ||
| Speed | ||
| Up Speed | ||
| Quality | Normal | |
| Fair | ||
| Draft | ||
| SmallLetter | ||
| Fine | ||
| Tool Select | ||
| Tool select | 1 2 3 4 S 72 F 110 Oo.250 S = speed F = force O = offset |
|
| Set smoothing Cut | Enabled | |
| Disabled | ||
| Overcut | ||
| Set Tangential Mode | Enabled | |
| Disabled | ||
| Pouncing | 0-200mm | |
| Panel Setup | Control panel only | |
| Accept setup command | ||
| Restore default? | ||
| Data Clear | ||
| Clear data memory | ||
| Firmware - File uploader | ||
| Port to use | USB port | Serial port |
| Operation | [Down] key + Power on | [CUT TEST] key + Power on |
| ValueCut Diagnostics menu - 3.03GA | Comment | |
| On/Offline key + Cut test + Power ON | ||
| DRAM checking | ||
| Hardware: 1.0 | ||
| FPGA: 1.1 | ||
| Use left / right arrow keys to enter menu | ||
| Check USB port? | ||
| Check Printer Port? | ||
| Check RS-232 19200? | ||
| Check RS-232 9600? | ||
| Holder down? | Enter = down On/Offline = up |
|
| Carriage Movement? | Y motor moving now (Left, Right arrow keys) | |
| Drum Movement? | X motor moving now (Forward, Backward arrow keys) | |
| Holder Encoder? | Holder encoder value -1 | |
| Y motor Encoder? | Y encoder reading | Move your pen head manually |
| X motor Encoder? | X encoder reading | Move your media manually |
| Check Width Sensor? | Now sensor is off | Move your pen head slowly passed your pressure rollers |
| Move carriage slowly | ||
| Check Media Sensors? | Now Front is Close | |
| Rear is Close | ||
| Check Lever Sensor? | Level is UP now | |
| Level is DOWN now | ||
| To exit diagnostics mode, press the On/Offline key | ||
| Exit Diagnostic Test | ||
| Please Reset Machine | ||